進口泰州SKF軸承安裝后，應進行一定的清洗和保養。所謂清潔度試驗是從滾動軸承中分離雜質并測量其污染的試驗方法。目前，清潔度檢測方法主要有三種：質量檢驗、顯微計數試驗和自動顆粒計數試驗。

After installation of imported SKF bearings in Taizhou, certain cleaning and maintenance should be carried out. The so-called cleanliness test is a test method for separating impurities from rolling bearings and measuring their contamination. At present, there are three kinds of cleanliness detection methods: quality inspection, microscopic counting test and automatic particle counting test.

1。自動顆粒計數試驗。

1. Automatic particle counting test.

基于光電理論和質量法的自動顆粒計算方法不同于顆粒計算方法。該方法具有較高的準確度，可直接測定雜質粒子的數量和大小。它通常適用于要求高清潔度的滾動軸承。

The automatic particle calculation method based on photoelectric theory and mass method is different from the particle calculation method. The method has high accuracy and can directly determine the number and size of impurity particles. It is usually suitable for rolling bearings requiring high cleanliness.

2。顯微鏡檢查。

2. Microscopic examination.

這種方法與質量方法相似。用顯微鏡直接觀察濾膜中雜質顆粒的大小和數量。不同之處在于，清洗液的化學成分和雜質含量可以在過濾后測定。該方法**適用于軸承精*密泰州SKF軸承的清潔度測量。它也可以基于雜質的形狀。

This method is similar to the quality method. The size and quantity of impurity particles in the filter membrane were observed directly with a microscope. The difference is that the chemical composition and impurity content of the cleaning solution can be determined after filtration. This method ** is suitable for measuring the cleanliness of SKF bearings in Mitai. It can also be based on the shape of impurities.

三。質量方法試驗。

Three. Quality method test.

進口軸承按J*B/T50-2005相關國家標準進行過濾、干燥、稱重。首先，將滾動軸承中的雜質清洗到清洗液中，計算雜質的質量。

The imported bearings are filtered, dried and weighed according to the relevant national standards of J*B/T50-2005. Firstly, impurities in rolling bearings are cleaned into the cleaning solution to calculate the quality of impurities.

軸承燒*傷的塑性變形

Plastic Deformation of Bearing Burns

在過大的靜載荷和沖擊載荷作用下，環形工件的滾子或滾道上出現不均勻的塑性變形坑。這經常發生在非常低的速度或擺動軸承。

Under excessive static and impact loads, uneven plastic deformation pits appear on the rollers or raceways of annular workpieces. This often happens at very low speeds or swing bearings.

泰州SKF軸承燒*傷的主要原因是滾動軸承的潤滑不*良，這可能是由于使用不規則的潤滑劑，或潤滑劑過多或不足，這是不正確的。所謂軸承燒壞狀態是指：滾道輪、滾動體及軸承保持架在旋轉過程中急劇加熱直至變色、軟*化、沉積和損壞。

Taizhou SKF bearing burns are mainly due to poor lubrication of rolling bearings, which may be due to the use of irregular lubricants, or excessive or insufficient lubricants, which is incorrect. The so-called bearing burnout state refers to: raceway wheel, rolling element and bearing cage are heated sharply in the process of rotation until discoloration, softening, deposition and damage.

也可能有太多的負載（過多的預載）。速度太高了。水或其*他異物入侵。間隙太小了。如果上述兩個條件都好，軸承箱的精度，即軸和軸的撓度。

There may also be too much load (too much preloading). The speed is too high. Water or other foreign bodies invade. The clearance is too small. If the above two conditions are good, the accuracy of the bearing box, that is, the deflection of the shaft and shaft.

研究要協調，軸承間隙和預緊，密封裝置要改進。檢查軸和軸承箱的精度。聽著，我想每個人都想知道答案。首先，選擇合適的滾動泰州SKF軸承潤滑劑及其用量，研究潤滑劑和潤滑方法，選擇合適的軸承。

Research should be coordinated, bearing clearance and pre-tightening, sealing device should be improved. Check the accuracy of shaft and bearing box. Listen, I think everyone wants to know the answer. Firstly, choose the appropriate lubricant and its dosage for rolling Taizhou SKF bearing, study the lubricant and lubrication method, and select the appropriate bearing.

通常，深溝球軸承的溫度隨著軸承工作的開始而緩慢上升，并在1-2小時后達到穩定狀態。軸承的正常溫度隨熱容、散熱、速度和機械負荷而變化。如果潤滑和安裝部件合適，軸承溫度將急劇上升，進口軸承將產生異常高溫。此時，我們必*須停止工作，采取必要的預防措施。

Usually, the temperature of deep groove ball bearings increases slowly with the start of the operation of the bearings, and reaches a stable state after 1-2 hours. The normal temperature of bearings varies with heat capacity, heat dissipation, speed and mechanical load. If the lubrication and installation parts are suitable, the bearing temperature will rise sharply, and the imported bearing will produce abnormal high temperature. At this time, we must stop working and take necessary precautions.

文章來自：泰州SKF軸承 www.wh-skf.com

Article from: Taizhou SKF Bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

Article from: Taizhou INA Bearing www.ina-China.cn

文章來自：泰州NSK軸承 www.klbbearings.com

Article from: Taizhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757