防銹材料的質量直接影響產品的加工質量。因此，在選擇防銹材料時，首先要根據質量要求對材料的理化性能進行檢測，然后通過中試對合格的材料進行檢測，以便根據質量大量使用。要求。獎賞。技術要求。泰州NSK軸承所選的防銹配件入廠后按不同材質的質量標準嚴格檢驗，合格后送供貨部使用。為了確保溶液的濃度和比例滿足工藝要求和使用性能，在使用過程中定期測試防銹材料和制備的溶液。建立完善的材料驗收體系和質量驗收標準，為防銹管理提供了可靠的保證。

The quality of antirust materials directly affects the processing quality of products. Therefore, in the selection of rust-proof materials, the physical and chemical properties of materials should be tested according to the quality requirements first, and then the qualified materials should be tested through pilot test, so as to be used in large quantities according to the quality. Requirement. Reward. Technical requirements. The rust-proof fittings selected by NSK bearings in Taizhou are strictly inspected according to the quality standards of different materials after they are imported into the factory and sent to the supply department for use after they are qualified. In order to ensure that the concentration and proportion of the solution meet the technological requirements and service performance, the rust-proof material and the prepared solution are regularly tested during the use process. The establishment of a sound material acceptance system and quality acceptance criteria provides a reliable guarantee for rust prevention management.

冷*卻水在泰州NSK軸承加工中具有許多功能，如冷*卻、潤滑、清洗、防銹等。正確使用和維護將直接影響工件的表面質量和刀*具的使用壽命。軸承冷*卻水大致可分為蘇打水、**化液和合成磨削液?；旧?，50t以上的液體可用于大規?；厥铡Ｓ投?、鐵屑、砂輪等磨削產品容易清洗，導致冷*卻水變質、加工零件燒*傷、生銹。加強冷*卻水的科學管理，可以提高冷*卻水的性能，保證泰州NSK軸承產品質量，降低冷*卻水的使用成本。

Cold water has many functions in the processing of NSK bearings in Taizhou, such as cold water, lubrication, cleaning, anti-rust and so on. Proper use and maintenance will directly affect the surface quality of the workpiece and the service life of the tool. Bearing cold water can be roughly divided into soda water, * * liquid and synthetic grinding fluid. Basically, more than 50t of liquid can be used for large-scale recycling. Grinding products such as oil ends, iron chips and grinding wheels are easy to clean, which results in deterioration of cold water, burns and rusts of processed parts. Strengthening the scientific management of cooling water can improve the performance of cooling water, ensure the quality of NSK bearings in Taizhou, and reduce the cost of using cooling water.

為了保證防銹技術的實施，科技部根據技術要求、零部件和生產設備的評價值，制定了具體的評價規則。**一*級防銹管理人員應當對生產設施進行月度工藝紀律*檢查，對冷*卻水、防銹液、清洗液、防銹油、腐蝕速度、清洗和涂油包裝的管理進行綜合檢查。NG。NG。對產品老化、管理水平和防銹人員的泰州NSK軸承監測項目進行全*面檢查。檢驗結果將分發給生產廠。從上到下，建立了防腐管理網絡，為防腐管理提供依據。

In order to ensure the implementation of anti-rust technology, the Ministry of Science and Technology has formulated specific evaluation rules according to the technical requirements, evaluation values of spare parts and production equipment. Grade I anti-rust managers shall conduct monthly process discipline inspection of production facilities, and conduct comprehensive inspection of the management of cold water, anti-rust fluid, cleaning fluid, anti-rust oil, corrosion rate, cleaning and oil-coated packaging. NG. NG. The product's aging, management level and anti rust personnel's Taizhou NSK bearing monitoring project will be inspected thoroughly. The inspection results will be distributed to the production plant. From top to bottom, an anti-corrosion management network has been set up to provide basis for anticorrosion management.

1。當大量軸承需要清洗時，應將油封和90～100℃之間的熱油清洗工具去除，然后用清水清洗多余的油，油加熱一段時間，然后進行**后一步熱蒸汽。

1. When a large number of bearings need to be cleaned, the hot oil cleaning tool between the oil seal and 90-100 C should be removed, then the excess oil should be cleaned with clean water, the oil heated for a period of time, and then the hot steam should be carried out after **.

2。清洗軸承表面時，應選擇清潔汽油和煤油進行清洗。確認后，清洗后，用干凈的布擦拭軸承，然后涂抹潤滑劑。然后按照泰州NSK軸承標準安裝過程安裝軸承。

2. When cleaning the bearing surface, clean gasoline and kerosene should be selected for cleaning. After /confirm/iation, after cleaning, wipe the bearings with clean cloth, then apply lubricant. Then install the bearing according to the installation procedure of Taizhou NSK bearing standard.

3。當所有的檢查都準備好加油和打開軸承時，軸承應該放置在清潔的液體中，如汽油中，然后整個軸承組應該輕輕旋轉，以獲得通道和碎片、清潔表面。

3. When all inspections are ready to refuel and open the bearings, the bearings should be placed in clean liquids, such as gasoline, and then the entire bearing group should be rotated gently to obtain passages and debris and clean surfaces.

文章來自：泰州SKF軸承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章來自：泰州NSK軸承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757