在泰州NSK軸承轉速上來說，軸承是根據軸承的類型，尺寸，精度，保持架類型，負荷，潤滑方式，及冷卻方式等因素確定。

In terms of the rotational speed of Taizhou NSK bearings, bearings are determined according to the type, size, accuracy, cage type, load, lubrication mode, and cooling mode of bearings.

軸承的安裝及拆卸，在特定應用場合需要常常拆卸及安裝，以確保可以按其地進行檢測及維修。內外圈可以分別安裝的軸承如：圓柱軸承，滾針軸承，及圓錐軸承十分合用于此場合。錐孔型的自動調心球泰州NSK軸承及自動調心滾子軸承在軸套的匡助下，同樣簡化了安裝程序。

Bearing installation and disassembly, in specific applications need to be often disassembled and installed to ensure that they can be inspected and maintained according to their location. Bearings such as cylindrical bearings, needle roller bearings and tapered bearings, which can be installed separately on the inner and outer rings, are very suitable for this occasion. Taizhou NSK bearing and automatic aligning roller bearing with taper pass can also simplify the installation procedure with the help of bushing.

在某些情況下滾動軸承要施加預壓以增加剛性，此程序通常用于深溝球軸承、向心推力球軸承及圓錐滾子軸承內外圈偏置，軸彎曲，軸或軸承箱公差變化，配合錯誤都會導致內外圈的偏心。為防止偏心角渡過大，自動調心球軸承，自動調心滾子軸承，或調心軸承座是較佳的選擇。嗓音頻率及扭矩，動彈泰州NSK軸承都是根據高精度尺度出產制造的，所以嗓音及扭力小。深溝球軸承、及圓柱滾子軸承合用對于對低嗓音，低扭力有特別要求的場合。

In some cases, rolling bearings have to be preloaded to increase rigidity. This program is usually used for deep groove ball bearings, centripetal thrust ball bearings and tapered roller bearings with inner and outer rings offset, shaft bending, axle or bearing box tolerance changes, and mismatch will lead to the eccentricity of inner and outer rings. In order to prevent excessive eccentricity, automatic self-aligning ball bearing, automatic self-aligning roller bearing or self-aligning bearing seat are better choices. The voice frequency and torsion, dynamic Taizhou NSK bearings are manufactured according to high precision scale, so the voice and torsion are small. Deep groove ball bearings and cylindrical roller bearings are used together for occasions with special requirements for low voice and low torsion.

(1)留意帶密封軸承不可用本法清洗，密封的內部應堅持原樣不可清洗。

(1) pay attention to the fact that sealed bearing can not be cleaned by this method, and the inside of the seal should be kept unclean.

(2)應將裝配外表用干凈的汽油、煤油、甲苯或二甲苯等溶液清洗干凈，并用干凈的抹布擦干，再涂上薄薄一層光滑油，這樣可使裝置操作起來便當效率。

(2) The assembly surface should be cleaned with clean gasoline, kerosene, toluene or xylene solution, wiped with a clean cloth, and then coated with a thin layer of smooth oil, so that the device can be operated easily and efficiently.

(3)臨裝置時翻開泰州NSK軸承封裝，將它浸入上述汽油等液體中以手輕緩地轉動，要保證堅持架，滾動體以及滾道外表的封裝油徹底被清洗干凈。

(3) When facing the device, open the package of Taizhou NSK bearing, immerse it in the above-mentioned gasoline and other liquids and rotate gently by hand, so as to ensure that the holder, rolling element and the packing oil on the raceway surface are thoroughly cleaned.

(4)清洗大量軸承時，先用溫度為90～100℃的熱機油淋燙以使封裝油凝結，同時用無縫口且不落屑的工具挖凈全部舊油，再淋燙幾分鐘，然后用煤油沖洗去機油，最后再用汽油清洗一遍。清洗干凈后，應戴上薄膜手套將泰州NSK軸承放在工作臺上的干凈的布上或紙上晾干。

(4) When cleaning a large number of bearings, first use hot engine oil at 90-100 degrees Celsius to condensate the package oil, at the same time use seamless and non-chipping tools to dig out all the old oil, then rinse the oil with kerosene for a few minutes, and finally wash it with gasoline. After cleaning, wear thin film gloves to dry Taizhou NSK bearings on clean cloth or paper on the worktable.

文章來自：泰州SKF軸承 www.wh-skf.com

The article is from: Taizhou SKF bearing www.wh-skf.com

文章來自：泰州INA軸承 www.ina-china.cn

The article is from: Taizhou INA bearing www.ina-china.cn

文章來自：泰州NSK軸承 www.klbbearings.com

The article is from: Taizhou NSK bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672